Properties of Buffers (College Board AP® Chemistry): Study Guide
Properties of buffers
A buffer solution is a solution which resists changes in pH when small amounts of acid or base are added
A buffer can consist of weak acid–conjugate base or weak base–conjugate acid
Acidic buffers
A common acidic buffer solution is an aqueous mixture of acetic acid and sodium acetate
Acetic acid is a weak acid and partially ionizes in solution to form a relatively low concentration of acetate ions
CH3COOH (aq) ⇌ H+ (aq) + CH3COO- (aq)
acetic acid ⇌ acetate
high conc ⇌ low conc
Sodium acetate is a salt which fully ionizes in solution
CH3COONa (s) → Na+ (aq) + CH3COO- (aq)
sodium acetate → acetate ion
low conc → high conc
There are reserve supplies of the acid (CH3COOH) and its conjugate base (CH3COO–)
The buffer solution contains relatively high concentrations of CH3COOH (due to the partial ionization of acetic acid) and CH3COO– (due to the full ionization of sodium acetate)
In the buffer solution, the acetic acid is in equilibrium with hydrogen and acetate ions
CH3COOH (aq) ⇌ H+ (aq) + CH3COO- (aq)
high conc. high conc.
Basic buffers
A basic buffer is made by mixing a solution of a weak base with its salt
E.g. NH3 (aq) and NH4Cl (aq)
In solution
NH3 (aq) + H2O (l) NH4+ (aq) + OH– (aq)
The equilibrium lies to the left as NH3 is a weak base
And
NH4Cl (aq) → NH4+ (aq) + Cl– (aq)
NH4Cl is a soluble salt so fully dissociated in solution
Therefore the mixture contains high concentrations of NH3 (aq) and NH4+ (aq) which will be able to react with any H+ and OH– added
Resisting pH change
The following reactions involving ammonia demonstrate how a buffer resists changes in pH
The conjugate base reacts with added acid, for example:
NH3 (aq) + H3O+ (aq) → NH4+ (aq) + H2O (l)
The conjugate acid reacts with added base, for example:
NH4+ (aq) + OH- (aq) → NH3 (aq) + H2O (l)
Examiner Tips and Tricks
A buffer contains large amounts of both members of a conjugate pair, such as CH3COOH and CH3COO-. So, make sure to name both by formula
OH- and water are not buffer components
When you explain buffer action, write the reaction of only the member that reacts, not the whole buffer. For example:
CH3COO- (aq) + H3O+ (aq) → CH3COOH (aq) + H2O (l)
A buffer resists pH change only when small amounts of acid or base are added. A large amount uses up one member and the pH then changes sharply
Worked Example
Which of the following combinations would form a buffer solution?
A. KI and Pb(NO3)2
B. NH3 and NH4NO3
C. HCl and HNO3
D. NaOH and KOH
Answer:
The correct answer is B, because:
This pair does form a buffer
NH3 is a weak base and NH4+ (from NH4NO3) is its conjugate acid, so the solution contains large amounts of both members of a conjugate pair
The NO3– ion is a spectator ion
A is incorrect because these are both salts and no acids or bases are present
C is incorrect because HCl and HNO3 are both strong acids
D is incorrect because NaOH and KOH are both strong bases
Choosing a buffer for a required pH
Buffers are best able to resist changes in pH when there is a near-equal concentration of the conjugate acid and base
I.e. when the pH = pKa of the acid/base pair
This is because a buffer with a pKa closest to the desired pH would be the best choice as it has the least adjusting to do in the base/acid ratio in order to reach the desired pH
For example, to make a buffer with a pH of 5.5, pyridine/pyridinium chloride (pKa of the pyridinium ion = 5.2) would be suitable
The ratio of [HA] to [A–] should be close to 1:1
But buffers are considered to be effective when the ratio is anywhere between 10:1 and 1:10
Unlock more, it's free!
Was this revision note helpful?
Build on this topic