Experimental Techniques (Cambridge (CIE) IGCSE Chemistry): Multiple Choice Questions

Exam code: 0620 & 0971

9 hours87 questions
1
1 mark

The diagram shows a burette and a measuring cylinder, both of which contain a liquid.

Diagram of a burette and a measuring cylinder showing volumes of liquid.

Which row shows the correct reading for both?

 

Burette

Measuring cylinder

A

18.4

34

B

18.4

56

C

17.8

34

D

17.8

56

    2
    1 mark

    Measuring volumes of liquids is a fundamental aspect of experimental chemistry. The diagram shows three different pieces of apparatus used for this task.

    q2-easy-mcq-12-1-experimental-techniques-cie-igcse-chemistry

    Which row is correct?

     

    1

    2

    3

    A

    burette

    measuring cylinder

    pipette

    B

    burette

    pipette

    measuring cylinder

    C

    pipette

    measuring cylinder

    burette

    D

    measuring cylinder

    burette

    pipette

      3
      1 mark

      A student dissolved ammonium chloride in water when investigating energy changes in reactions.

      Which terms best describes each substance?

       

      ammonium chloride

      water

      A

      solute

      solvent

      B

      solvent

      solution

      C

      solution

      solvent

      D

      solute

      solution

        4
        1 mark

        A student prepared crystals of copper sulfate from copper carbonate and sulfuric acid.

        The student separated the excess copper carbonate from the solution using filtration. 

        What word describes the excess copper carbonate?

        • Residue

        • Filtrate

        • Solvent

        • Solution

        5
        1 mark

        A student carries out a titration to determine the volume of hydrochloric acid needed to neutralise 25 cm3 of sodium hydroxide. 

        She measured 25 cm3 sodium hydroxide into a conical flask. 

        Which piece of equipment should she use to do this?

        • Burette

        • Measuring cylinder

        • Beaker

        • Pipette

        6
        1 mark

        A student measures the time taken for 2.0 g of magnesium to dissolve in 50 cm3 of dilute sulfuric acid.

        Which apparatus is essential to complete the experiment?

        1. stop-clock 

        2. measuring cylinder 

        3. thermometer 

        4. balance

        • 1, 2 and 4

        • 1 and 2 only

        • 1 and 4 only

        • 2, 3 and 4

        7
        1 mark

        A student investigates the effect of temperature on the rate of reaction between large lumps of calcium carbonate and dilute acid. The student plots a graph of the loss in mass of the reaction mixture against time for different temperatures.

        Which combination of apparatus are essential to record the measurements used to plot the graph?

        • thermometer, balance and stop-watch

        • thermometer, gas syringe and stop-watch

        • balance, gas syringe and stop-watch

        • thermometer, inverted measuring cylinder and stop-watch

        8
        1 mark

        A student carries out a titration to determine the concentration of a dilute acid using a standard alkali.

        Five actions in this acid-base titration are shown in the table.

        step

        action

        P

        record the final burette reading after the end-point is reached

        Q

        transfer a measured volume of alkali into a conical flask using a volumetric pipette

        R

        add a few drops of a suitable indicator to the flask

        S

        note the initial burette reading before starting the titration

        T

        carefully run the acid from the burette into the flask while swirling until a permanent colour change occurs

        • Q → R → S → T → P

        • Q → S → T→ P→ R

        • S → T → P→ Q→ R

        • Q → R → T → S → P

        9
        1 mark

        A student fills a burette with dilute nitric acid, exactly to the zero mark, and records the initial reading in a results table.

        All of the other readings in the table are recorded to one decimal place.

        Which initial reading is recorded in the same way as the other readings in the table?

        • 0

        • zero

        • 0.0

        • 0.00

        10
        1 mark

        A student carries out a titration and records the burette readings shown.

        final burette reading / cm3

        27.5

        initial burette reading / cm3

        4.0

        What is the volume of solution used?

        • 4.0 cm3

        • 23.5 cm3

        • 27.5 cm3

        • 31.5 cm3

        11
        1 mark

        A student titrates dilute hydrochloric acid against aqueous sodium hydroxide.

        A volumetric pipette is used to add 25.0 cm3 of the aqueous sodium hydroxide to a conical flask. The dilute hydrochloric acid is added from a burette.

        Where should the indicator be added?

        • to the dilute hydrochloric acid in the burette

        • to the aqueous sodium hydroxide in the conical flask

        • to the dilute hydrochloric acid in the burette and to the aqueous sodium hydroxide in the conical flask

        • to the conical flask once the end point has been reached

        12
        1 mark

        A student carries out an acid-base titration using thymolphthalein as the indicator.

        Which row shows the colour of thymolphthalein in an acid and in an alkali?

        in an acid

        in an alkali

        A

        colourless

        blue

        B

        blue

        colourless

        C

        yellow

        red

        D

        red

        yellow

          1
          1 mark

          A student wants to investigate the rate of reaction between marble chips and hydrochloric acid by measuring the volume of carbon dioxide produced with different concentrations of acid.

          The equation for the reaction is as follows:

          2 HCl + MgCO3 → MgCl2 + CO2 + H2O

          Which of the following lists of equipment can she use to measure the volume of the gas produced?

          • Gas syringe, cotton wool, bung, delivery tube

          • Gas syringe, conical flask, bung, delivery tube

          • Gas syringe, beaker, bung, balance

          • Balloon, conical flask, stopper, balance

          2
          1 mark

          The steps below are for an acid-base titration. 

          1

          Record the final volume of hydrochloric acid in the burette

          2

          Add hydrochloric acid from the burette into the conical flask until the indicator changes colour

          3

          Record the initial volume of hydrochloric acid in the burette 

          4

          Add a fixed volume of sodium hydroxide to a conical flask using a pipette 

          5

          Add indicator

          What is the correct order of these steps?

          • 3  →  4 →  2  →  5  → 1

          • 4  →  3 →  2  →  1  → 5 

          • 4  →  5 →  3  →  2  → 1 

          • 5  →  3 →  2  →  1  → 4

          3
          1 mark

          A student is following the written procedure for an experiment. The instruction states:

          'Quickly add 25 cm3 of sodium hydroxide'

          Which piece of apparatus would be most suitable to use?

          • Burette

          • Conical flask

          • Measuring cylinder

          • Volumetric pipette

          4
          1 mark

          W, X, Y and Z are pieces of laboratory apparatus.

          12-1-q2-cie-igcse-mcq-experimental-techniques-hard

          Which row describes the most appropriate use of the apparatus for the measurement taken?

           

          Apparatus

          Measurement taken

          A

          W

           0.5 cm3 of acid to add to marble chips in a rate of reaction investigation

          B

          X

           20 cm3 of sodium hydroxide for use in a titration

          C

          Y

           26.70 cm3 of hydrochloric acid added to sodium hydroxide in a titration

          D

          Z

           85 cm3 of gas given off in a rate of reaction investigation

            5
            1 mark

            A student decided to investigate the rate of reaction between marble chips and dilute hydrochloric acid at 35 oC. 

            She had access to the following apparatus:

            W a balance

            X a thermometer

            Y a measuring cylinder

            Z a stopwatch

            Which pieces of apparatus did she use?

            • X, Y and Z only

            • W, Y and Z only

            • W, X and Z only

            • W, X, Y and Z

            6
            1 mark

            Five steps in an acid–base titration are shown.

            1. Slowly add the acid from a burette into a conical flask until the indicator becomes colourless.

            2. Add thymolphthalein.

            3. Use a volumetric pipette to add a fixed volume of alkali to a conical flask.

            4. Read and record the initial volume of acid in the burette.

            5. Read and record the final volume of acid in the burette.

            What is the correct order of these steps to complete an acid–base titration?

            • 2 → 4 → 1 → 5 → 3

            • 3 → 2 → 4 → 1 → 5

            • 3 → 4 → 1 → 5 → 2

            • 4 → 3 → 1 → 2 → 5

            7
            1 mark

            A student carries out four titrations, adding dilute hydrochloric acid from a burette to 25.0 cm3 of aqueous sodium hydroxide.

            Between titrations the conical flask is emptied and rinsed.

            Which liquid should be used to rinse the conical flask?

            • the aqueous sodium hydroxide

            • distilled water

            • the dilute hydrochloric acid

            • The flask should be emptied but not rinsed.

            8
            1 mark

            During a titration a student stands the conical flask on a white tile.

            Why is the white tile used?

            • to reflect light through the solution so the indicator reacts faster

            • to insulate the flask from the bench so the temperature does not change

            • to hold the conical flask steady while it is swirled

            • to make the colour change at the end point easier to see

            9
            1 mark

            Part of a student's titration method is shown.

            Add the acid from the burette, swirling the flask after each addition. Near the end point, add the acid one drop at a time.

            Why is the acid added one drop at a time near the end point?

            • to make sure the solution in the flask is mixed after each addition

            • to stop the reaction in the flask becoming too exothermic

            • to avoid adding more acid than is needed to reach the end point

            • to give the indicator time to dissolve in the solution

            10
            1 mark

            A student uses a volumetric pipette to add 25.0 cm3 of aqueous potassium hydroxide to a conical flask, then adds a few drops of thymolphthalein indicator.

            Dilute sulfuric acid is run in from a burette until the end point is reached.

            What colour change is seen in the conical flask?

            • blue to colourless

            • colourless to blue

            • blue to yellow

            • colourless to pink

            1
            1 mark

            A student prepared crystals of potassium(II) chloride by the following method.

            1

            25.0 cm3 of dilute hydrochloric acid was accurately measured into a conical flask using a measuring cylinder

            2

            Aqueous potassium hydroxide was added from a burette until the solution was neutral

            3

            The solution was evaporated and the crystals washed with approximately 20 cm3 of water measured using a pipette

            Which steps do not use the most appropriate piece of apparatus for the measurement taken?

            • 1, 2 and 3

            • 1 and 2 only

            • 1 and 3 only

            • 2 and 3 only

            2
            1 mark

            A student prepared a solution of copper(II) sulfate by mixing dilute sulfuric acid with an excess of copper(II) oxide.

            They filtered the mixture using the apparatus below.

            12-1-q4-cie-igcse-mcq-experimental-techniques-hard

            Which terms best describes each substance?

             

            Solvent

            Solute

            Filtrate

            Residue

            A

            water

            copper(II) sulfate

            copper(II) sulfate solution

            copper(II) oxide

            B

            dilute hydrochloric acid

            copper(II) oxide

            water

            copper(II) oxide

            C

            water

            copper(II) sulfate solution

            copper(II) oxide

            copper(II) sulfate

            D

            copper(II) sulfate solution

            water

            dilute hydrochloric acid

            water

              3
              1 mark

              A student performed a titration to find the volume of hydrochloric acid required to neutralise 25.0 cm3 of sodium hydroxide using the following method.

              • Add a fixed volume of sodium hydroxide to a conical flask using a measuring cylinder

              • Add methyl orange indicator

              • Record the initial volume of hydrochloric acid in the burette 

              • Add hydrochloric acid from the burette into the conical flask until the indicator changes colour

              • Record the final volume of hydrochloric acid in the burette

              Another student suggested the following changes.

              1

              Use a pipette to measure the sodium hydroxide

              2

              Use universal indicator as the indicator

              3

              Repeat the experiment until the results are concordant

              4

              Ensure that the initial volume of hydrochloric acid reads 0.00 cm3 on the burette

              Which suggestions would improve the experiment?

              • 1 and 2

              • 1 and 3

              • 2 and 3

              • 3 and 4

              4
              1 mark

              A student titrated sodium carbonate solution against 25 cm3 of hydrochloric acid. 

              They used methyl orange as an indicator.

              What is the colour changed observed at the end point?

              • red to yellow

              • yellow to orange

              • yellow to red

              • red to orange

              5
              1 mark

              Why is it important to fill the space below the tap in a burette with acid or alkali before beginning a titration?

              • To give a more accurate result

              • The burette's scale does not include this volume

              • To give concordant results

              • An incorrect volume would be recorded

              6
              1 mark

              A student does a rough titration, which is not shown, and then four accurate titrations.

              The burette readings for the four accurate titrations are shown.

              titration

              1

              2

              3

              4

              initial reading / cm3

              0.0

              0.8

              1.2

              0.5

              final reading / cm3

              24.8

              25.6

              27.3

              25.3

              Results are concordant when they are within 0.10 cm3 of each other.

              The mean volume is calculated from all of the concordant results.

              Which titrations should the student use to calculate the mean volume?

              • 1, 2 and 4

              • 1, 2, 3 and 4

              • 1 and 2 only

              • 2, 3 and 4

              7
              1 mark

              Which statement about apparatus used to measure the volume of a liquid is correct?

              • A burette is designed to deliver one fixed volume accurately.

              • A volumetric pipette is designed to deliver any volume between 0.0 cm3 and 25.0 cm3.

              • A measuring cylinder is designed to measure an approximate volume.

              • The graduations on a beaker give as close a reading of volume as those on a measuring cylinder.

              8
              1 mark

              A student follows this instruction from a method.

              "Add about 50 cm3 of distilled water to the beaker."

              Which row gives the most suitable apparatus for this step, and the correct reason?

              Apparatus

              Reason

              A

              volumetric pipette

              it delivers a fixed volume accurately

              B

              burette

              it measures any volume between 0.0 cm3 and 50.0 cm3

              C

              measuring cylinder

              this volume does not need to be measured precisely

              D

              beaker

              its graduations measure volume accurately

                9
                1 mark

                A student uses this method to find the concentration of an acid.

                • Use a volumetric pipette to add 25.0 cm3 of the acid to a conical flask

                • Add a few drops of thymolphthalein

                • Run aqueous sodium hydroxide into the flask from a burette until the end point is reached

                For which acid would this method not give a reliable value for the volume of sodium hydroxide used?

                • a colourless solution of ethanoic acid

                • a colourless solution of sulfuric acid

                • a dark brown vinegar, which contains ethanoic acid

                • a colourless solution of nitric acid

                10
                1 mark

                A burette is to be filled with a dilute acid for a titration.

                The burette is washed immediately before it is filled.

                Which washing gives an accurate volume of acid used?

                • distilled water only

                • distilled water, then the dilute acid

                • the aqueous alkali only

                • distilled water, then the aqueous alkali