Reaction Energy Profiles (College Board AP® Chemistry): Study Guide

Oluwapelumi Kolawole

Written by: Oluwapelumi Kolawole

Reviewed by: Stewart Hird

Updated on

Elementary reactions & bonds

  • Collision theory says that particles must collide with at least the activation energy and a suitable orientation

    • Transition state theory explains what happens to the bonds during the collision

  • In elementary reactions, the energy from the collision of reactant molecules is used to break bonds before products are formed

  • Bond breaking and bond making, in relation to activation energy, are described by the transition state theory of reaction rate

Transition state theory

  • Transition state theory explains the reaction resulting from the collision of two molecules in terms of an activated complex

    • An activated complex is an unstable, high-energy species that must be formed before the reaction can occur

  • The transition state is the highest-energy arrangement of atoms along the reaction path, where bonds in the reactants are partly broken and bonds in the products are partly formed

    • It is not an intermediate as an intermediate is produced in one step and used up in a later step

  • For example, the reaction between carbon monoxide, CO, and nitrogen dioxide, NO2:

  • At lower temperatures:

  • At higher temperatures (above about 500 K):

    • The reaction happens in one step

    • The activated complex is made up of CO and NO2 molecules in close contact

    • In this activated complex, the N—O bond in the NO2 molecule has been partially broken and a new bond between carbon and oxygen has started to form

    • The dotted lines stand for “partial bonds” in the activated complex

Activated complex

Reaction path in three stages. Reactants: carbon monoxide, O≡C, and nitrogen dioxide, O–N=O. Activated complex: O≡C---O---N=O, with dashed partial bonds between C and O and between O and N. Products: carbon dioxide, O=C=O, and nitrogen monoxide, N=O

A diagram showing the reaction path involving the formation of activated complex

  • One advantage of the transition state theory is that it explains why the activation energy of reactions is much smaller than the energy required to break the bonds in reacting molecules

    • Forming the activated complex only weakens the old bonds while the new ones start to form, so it needs much less energy than breaking the old bonds completely

    • In the reaction above, the activation energy is 134 kJ/mol

    • This is considerably smaller than the amount of energy required to break the bonds in the reactants:

      • C≡O 1075 kJ/mol

      • N=O 607 kJ/mol

      • N–O 222 kJ/mol

Energy profiles

  • The changes in the energies of the reactants during collision can be described by an energy profile

    • This can also be known as a potential energy diagram

  • Based on the transition state theory, the collision of reactant molecules results in a change in their kinetic and potential energies

    • As molecules collide, their kinetic energy is converted to potential energy

    • After collision, the products formed recoil and the potential energy is reconverted to kinetic energy

  • An energy profile plots potential energy against the reaction coordinate

    • The reaction coordinate is the axis along which the complex set of motions that rearrange reactants into products can be plotted

  • The profile runs from reactants, through a transition state, to products

Energy profile diagram

Energy profile with energy on the vertical axis and reaction coordinate on the horizontal axis. Reactants, CO + NO₂, rise over a single peak labeled activated complex and fall to products, CO₂ + NO, at a lower level. Arrows show Eₐ (forward reaction) = 134 kJ and ΔH = −226 kJ

A diagram showing the changes in the energy for the reaction between CO and NO2. During the reaction initiation, the activation energy (Ea) of 134 kJ must be given to the reactants for every mole of CO that reacts

  • From the energy profile diagram for the reaction between CO and NO2 shown above:

    • The reactants are at a higher energy level than the products, which means the reaction is exothermic

      • The overall difference in this potential energy is known as the enthalpy change, ΔH, of the reaction

      • When reactants have less energy than products, the reaction is said to be endothermic

    • The difference between the maximum energy and the energy of the reactant indicates the activation energy, Ea of the forward reaction

    • The top of the activation energy barrier represents the transition state

      • The chemical species that exists at this transition point is called the activated complex

Activation energy and reaction rate

  • The rate of a reaction is dependent on the magnitude of Ea and not on the enthalpy change

    • Slow reactions have high activation energy

    • Fast reactions have low activation energy

  • This is because, for a slow reaction, only a small fraction of collisions have energy equal to or greater than the activation energy

  • There is no way to predict the activation energy of a reaction from its enthalpy change

    • A highly exothermic reaction may be very slow because it has a high activation energy

    • On the other hand, an endothermic reaction may be very fast because it has a low activation energy

  • The activation energy for the reverse reaction is simply the difference between the potential energy of products and the maximum energy of the curve

    • For example, for the reaction between CO and NO2:

Ea (forward) = +134 kJ/mol

ΔH = −226 kJ/mol

Ea (reverse) = Ea (forward) − ΔH = 134 − (−226)

Ea (reverse) = 360 kJ/mol

Examiner Tips and Tricks

If a question asks why a reaction is slow or needs a high temperature, answer with activation energy (kinetics), not with ΔH. On an energy profile, draw Eₐ from the reactant level to the peak, and ΔH from reactants to products.

Unlock more, it's free!

Join the 100,000+ Students that ❤️ Save My Exams

the (exam) results speak for themselves:

Build on this topic

Oluwapelumi Kolawole

Author: Oluwapelumi Kolawole

Expertise: Chemistry Content Creator

Oluwapelumi is a Pharmacist with over 15000+ hours of AP , IB, IGCSE, GCSE and A-Level chemistry tutoring experience. His love for chemistry education has seen him work with various Edtech platforms and schools across the world. He’s able to bring his communication skills as a healthcare professional in breaking down seemingly complex chemistry concepts into easily understood concepts for students.

Stewart Hird

Reviewer: Stewart Hird

Expertise: Chemistry Content Creator

Stewart has been an enthusiastic GCSE, IGCSE, A Level and IB teacher for more than 30 years in the UK as well as overseas, and has also been an examiner for IB and A Level. As a long-standing Head of Science, Stewart brings a wealth of experience to creating Topic Questions and revision materials for Save My Exams. Stewart specialises in Chemistry, but has also taught Physics and Environmental Systems and Societies.